|
IGT S+ Slot Machine Game Change
|
|
Top Glass
|
|
|
Reel
Glass |
|
Belly Glass
|
|
| |
| Replace your Slot Machine Glass pieces with the
new ones that were sent to you in the kit. Some game kits only require 2 pieces
of glass and others use all 3.The top piece
of glass removes by opening the slot machine main door and carefully lifting
the old glass holder up and out of the cabinet frame.
Install the new upper glass.
If your new kit included the (Reel) glass remove
the old piece by removing the florescent lamp bulb and then
removing the florescent fixture screws and then the fixture itself. Once the
fixture is removed you should be able to grab the old reel glass on both sides
and carefully wiggle it out of the lower holder and replace it with the new piece
of glass. (Be sure that all of your stickers are attached to the new glass before
installing the light and fixture.The belly or lower glass is replaced by locating the glass door release knob which is located on the main machine door. Simply pull the
knob straight out and flip the frame of the lower glass assembly down. Remove
the small screws (up to 4 of them) from the light/glass holder and carefully
slide the old glass out of the machine. When installing the new lower glass be
sure that it is right side up when the assembly is closed before tightening the
screws that hold it in place.
| |
Slot Machine Reel Strips
|
Your new slot kit includes 3 reel replacement reel strips.They
are to be installed in your reel baskets in the correct numerical order for your
particular game |
|
|
The Reels will be numbered in the order that they are installed in the reels from left to right
|
The Reels will be numbered in the order that they are installed in the reels from left to right
|
The Reels will have numbers on them and should be in order from left to Right.
(They may or may not look like the above example) |
|
Lay out the new strips on a flat surface
and take a comparison look at the strips different symbols. If they are all the
same and all the symbols line up with each other then you do not need to be concerned
with which strip goes to which reel. If however, any strips are different from
each other than you will need to install them in a particular order depending
on the game. |
|
|
Your new reel strips have small notches cut
in them at the bottom. There is also a matching notch on each reel basket. The
notches on both the reel strips and the reel baskets must be installed so that
their notches are aligned to together in the correct positions in their reel
baskets. In addition most (Not all) strips will be numbered either at the very
bottom or on the back top side of the strip. Generally the lowest number strip
will be installed in the left reel, usually marked as #1 and the next higher
# strip will go to the middle reel and the last one installed at the most right
side reel. There is an exception to this rule that being if your reel strip set
has different symbols, you will install the odd number strip in the middle or
right side depending on your game.
The easiest way to locate the notches in the reel baskets is to place a reel
strip into the left side groove of the basket that it is to be installed into
and hold the strip at a 45 degree angle to the basket with one hand and use the
other hand to rotate the basket slowly until you feel it catch on the notch.
Then, proceed to roll the strip around the back side of the basket and as you
do tuck both sides into the grooves of the basket until you come back around
to where you started. At this time you want to make sure that the end of the
reel strip overlaps the other end of the strip and that they are seated together
with the self adhesive sticky surface on the inside of the strip. (You may have
to use clear scotch tape to secure the strip to itself. If you did this correctly,
you will not be able to see the notches in the strips after you are finished
and the reel should spin straight and true. numbers on the bottoms or back sides
of the strips so that they are installed in the correct reel. |
|
|
|
Slot Machine Eprom
Chips
|
If you change the "Game" Eprom
chip you will loose the operational function of your Bill Validator and it will
require a special Set Chip to re-activate it. Because of this,
most Game Kits will not include the Game Eprom. |
|
Remove IGT S+ MPU Processor Board
|
Locate the black round handle that looks
kind of like a closet or cabinet door knob. Grab a hold of it and lift straight
up to remove the main system board from the lower board (Use caution and Do not
use too much force to avoid damaging the lower board) Place the board in a lighted
area so you can locate your Eprom game and reel chips. (The 2 chips are clearly
labelled on the board) - Take Notice that there is a notch in each chip at one
end and pay close attention to which direction that notch is in relation to the
direction the board. (See photo below) - The new chip(s) must be installed in
the same direction! |
|
Install the new IGT S+ "REEL" Eprom
chip that was included with your game kit in the same direction as the old one
that you just removed. This means the notch in the chip must install in the same
direction. Use caution when installing
the chip so that you do not fold over any of the chips pins .Go slowly and re-check
all the legs as you go and again afterwards. If one or more
of the legs do get bent, you must straighten
it before proceeding. Next, push down on the top of
the chip firmly until the chip is seated all
the way in its holding socket. If you were instructed to also
change the
"GAME" chip with your new kit now is the time
to do that following the same guidelines as above. You are now ready to install
the system board and bring up the machine to set the games options. |
|
|
Install
IGT S+ Slot Machine MPU Board
| Make sure you reinstall the main board the same
as it was removed. The board must align on both sides of the board holder. It
also must be completely seated down against the lower board. Use care to be sure
both sides are square during this procedure and Don't use exccessive force when
seating it down against the bottom board or you risk damaging the pins that are
located on the bottom. |
Initialize IGT S+ Slot Machine
|
After
installing the main system board. Install the hopper and turn the
power switch on. The machine shiould come to life and you should see a "61" displayed
in the winner paid window. - You may see a 65, 66 or 67
in the window instead. See the below
illustrations and pictures to see what you need
to do for each code displayed: |
|
 |
 |
 |
 |
If
you see a "65, 66, or 67"code after making a chip change - Power off the machine,
then back on. You should then see a 61 displayed in the winner paid
window. |
When you get a 61 code displayed |
Press
and hold the test button until you hear a "Ding" and see a 61 - 1 code displayed |
Once
you get a 61- 1 close door completely and turn
the rest key one time |
Note:
- A Common problem that occurs after a game chg
is that you will see a 61- 1 code after you hold the test button in and hear
the "Ding" but
you close the door and turn the reset key and nothing happens. This is usually
caused by an open door to the cash box or bad/misaligned door optics. |
| |
|
|
IGT Reel Slots
IGT
Slot Conversion
